Effect | Instruction | illustrate |
Enable configuration of audio and video encoding parameters | <VariCfgSec Action="DEVICE_SET"> <stMainStream ucFD_VideoMode="0" ucFD_VEncFormat="0" ucFD_AEncFormat="0" ucFD_VolumeIn="15" ucFD_VolumeOut="15" ucFD_ExternalAHD="1"> <stVideoPara> <VChn_0 ucFD_ChnValid="1" uiFD_ValidResBitFlag="52" ucFD_Resolution="6" ucFD_Quality="0" ucFD_FrameRate="25" ucFD_Gop="25" uiFD_BitRate="4096" uiFD_DisableAudio="0" uiFD_DisableVideo="0" /> <VChn_1 ucFD_ChnValid="1" uiFD_ValidResBitFlag="52" ucFD_Resolution="6" ucFD_Quality="0" ucFD_FrameRate="25" ucFD_Gop="25" uiFD_BitRate="4096" uiFD_DisableAudio="0" uiFD_DisableVideo="0" /> <VChn_2 ucFD_ChnValid="1" uiFD_ValidResBitFlag="52" ucFD_Resolution="6" ucFD_Quality="0" ucFD_FrameRate="25" ucFD_Gop="25" uiFD_BitRate="4096" uiFD_DisableAudio="0" uiFD_DisableVideo="0" /> <VChn_3 ucFD_ChnValid="1" uiFD_ValidResBitFlag="52" ucFD_Resolution="6" ucFD_Quality="0" ucFD_FrameRate="25" ucFD_Gop="25" uiFD_BitRate="4096" uiFD_DisableAudio="0" uiFD_DisableVideo="0" /> </stVideoPara> </stMainStream> </VariCfgSec> | ucFD_VideoMode: video format (0 PAL format, 1 NTFS format) ucFD_VEncFormat: Video coding technology (1 H265, 0 H264 encoding technology) ucFD_AEncFormat: Audio encoding format (0 G726, 1 G711A, 2 G711u) ucFD_VolumeIn: Video input volume level (Range 0-18 from small to loud 0 mute) ucFD_VolumeOut: video output volume (Range 0-18 from small to loud 0 mute) VChn_0: Configure the first camera channel parameters (VChn_1 second channel, VChn_2 third channel, VChn_3 fourth channel); ucFD_Resolution: image resolution (4=D1, 5=720P, 6=1080P); ucFD_FrameRate: frame rate, default 25 frames; uiFD_BitRate: bit rate; uiFD_DisableAudio: Audio encoding switch (0 on, 1 off) uiFD_DisableVideo: Video encoding switch (0 on, 1 off) |
Configure substream parameters | <VariCfgSec Action="DEVICE_SET"><stSubStream ucFD_FrameRate="25" uiFD_BitRate="512" /></VariCfgSec> | UcFD_FrameRate: frame rate; UiFD_BitRate: bit rate |
Modify boot mode | <VariCfgSec Action="DEVICE_SET"><stPower ucPowerMode="0"/></VariCfgSec> | ucPowerMode="0" 0 is ACC mode, 1 is timing mode |
Tick the UI Shutdown Delay checkbox | <VariCfgSec Action="DEVICE_SET"><stPower ucPOnDelayEnable="1"/></VariCfgSec> | |
Modify the shutdown delay time | <VariCfgSec Action="DEVICE_SET"><stPower usPOffDelayTime="500"/></VariCfgSec> | usPOffDelayTime="500" Units Minutes |
Modify device UI language | <VariCfgSec Action="DEVICE_SET"><stDisplay strLanguage="US"/></VariCfgSec> | strLanguage="US" for English, change to CN for Chinese |
Modify GPS mode | <VariCfgSec Action="DEVICE_SET"><stBaseInfo ucFD_GpsMode="2" /></VariCfgSec> | ucFD_GpsMode="2" 2 is GPS/BD mode; 0 is GPS mode; 1 is BD mode |
Set up IPC | <VariCfgSec Action="DEVICE_SET"><stIpc ucFD_Enable="1" ucFD_IPCNum="4" strFD_User="admin" strFD_Pass="Admin123"><stChnIpc><Chn_0 uiFD_IP="" /><Chn_1 uiFD_IP="" /><Chn_2 uiFD_IP="" /><Chn_3 uiFD_IP="" /></stChnIpc></stIpc></VariCfgSec> | ucFD_Enable="1" means enable IPC function, 0 means disable IPC function; ucFD_IPCNum="4" means enable 4 IPC channels; strFD_User="admin" means use admin to access IPC; strFD_Pass="Admin123" means Use the password of Admin123 to access the IPC; Chn_0 uiFD_IP="" Fill in the IP address of the corresponding IPC here, indicating the image to configure the first IPC channel, and so on |
Tick the UI IPC checkbox | <VariCfgSec Action="DEVICE_SET"><stRecord ucFD_EnableIPC="1"/></VariCfgSec> | |
Modify the recording mode | <VariCfgSec Action="DEVICE_SET"><stRecord ucFD_RecordMode="0"/></VariCfgSec> | ucFD_RecordMode="0" 0 means boot recording; 1 means alarm recording; 2 means timing recording; 3 means manual recording |
Modify SD card usage | <VariCfgSec Action="DEVICE_SET"><stRecord ucFD_SDUsage="3"/></VariCfgSec> | ucFD_SDUsage="3" 3 means mirror recording; 0 means no recording; 1 means loop recording; 2 means missing recording; |
Set up timed snapshots | <VariCfgSec Action="DEVICE_SET"><stSnap ucFD_SaveDays="7" ucFD_MultiSnapEnable="0" uiFD_Interval="300" ucFD_SnapCount="1" /></VariCfgSec> | ucFD_SaveDays="7" means the number of days to save snapshots; ucFD_MultiSnapEnable="0" 0 means do not enable timing snapshots, 1 means enable timing snapshots; uiFD_Interval="300" means the interval between snapshots is 300 seconds; |
Open Gsensor | <VariCfgSec Action="DEVICE_SET"><stOSD ucFD_GSensorEnable="1" /></VariCfgSec> | ucFD_GSensorEnable="1" 1 means enable Gsensor, 0 means close Gsensor |
set USB mode | <VariCfgSec Action="DEVICE_SET"><stRecord ucFD_UsbUsage="1" /></VariCfgSec> | ucFD_UsbUsage="1" 1 means ADAS mode, 0 means USB mode |
Turn on the helmet alarm upload function | <VariCfgSec Action="DEVICE_SET"><stNetWorkMode usFD_ExtFunBitFlag="1" ></VariCfgSec> | |
AHD and NVR mode switching | <VariCfgSec Action="DEVICE_SET"><stIpc ucFD_PureNVR ="1" /></VariCfgSec> | ucFD_PureNVR="1" means enable NVR mode, change to 0 is AHD mode |
Turn on face recognition | <VariCfgSec Action="DEVICE_SET"><stIpc ucFD_Enable="1" usFD_FuncMode="1" ></VariCfgSec> | usFD_FuncMode="1" 1 means face recognition is turned on, 0 is turned off |
M91A enables illegal area intrusion detection function | <VariCfgSec Action="DEVICE_SET"><stIpc ucFD_Enable="1" usFD_FuncMode="2" ></VariCfgSec> | |
Configure the M91A face recognition alarm time | <VariCfgSec Action="DEVICE_SET"><stIpc><stFunTPeriod><TPeriod_0 ucFD_Valid="1" strFD_Wday="1111111" strFD_StartT="00:00:00" strFD_EndT="23:59:59" /></stFunTPeriod></stIpc></VariCfgSec> | This configuration parameter is always recognized and alarmed by default. |
Modify OSD overlay channel name | <VariCfgSec Action="DEVICE_SET"><stChnOSD><stChnOSDPara><VChn_0 strFD_ChnName="indoor" /><VChn_1 strFD_ChnName="the front" /><VChn_2 strFD_ChnName="route" /><VChn_3 strFD_ChnName="offside" /><VChn_4 strFD_ChnName="rear" /><VChn_5 strFD_ChnName="left side" /><VChn_6 strFD_ChnName="
| VChn_0 strFD_ChnName="indoor" means to configure the first camera channel screen OSD character superimposed name is called "indoor" |
format the hard drive | <VariCfgSec Action="DEVICE_FORMAT"><stDiskDiskNo="0"></VariCfgSec> | stDistDistNo="0" means format the hard disk, change to 1 means format the SD card |
Recording channel still remains after ACC is closed | <VariCfgSec Action="DEVICE_SET"><stPower uiAccOffStopRecCh="15"/></VariCfgSec> | uiAccOffStopRecCh="15" closes 1-4 channels 0 opens all channels |